Do they also have the „click“ on the up position? Amazon reviews are full of horror stories, and I hope that would get fixed.
Also, do they still support Amiibos?
Nice. I’d replace the plastic buckle lock with metal ones, too, if you’re already opening up the joycon.
Please don’t put the electronics directly on the magnetic mat.
Wait, why?
Let’s be clear, it’s really low risk, especially for such a low strength one, but some types of components can get damaged by it, or you could end up dislodging badly soldered or already damaged ones while you move the board around.
In the worst case, if you dislodge them just enough to give you an intermittent problem, good luck debugging it.
I just feel that it’s not worth risking it.
How are they? Can you tell much of a difference in terms of fine accuracy compared to stock?
From my experience they felt a bit stiffer than the original sticks but that went away eventually. They feel just like the original sticks now. Definitely worth doing, and it’s not too hard to do, it’s just time consuming since the joycon parts are so small!
those are the ones without drift right??
Yeah the sticks use magnets rather than any physical contact to determine their positions, so there is no risk of the kind of wear that causes drift
This needs to be a standard with them all, period
Anyone with experience with joysticks (these or regular ones), I have a weird backlash issue with my Steam Deck where if I pull the joystick all the way in one direction and release it, it will overshoot the center and go ever so slightly in the other direction, and weirdly enough its only a recent issue and did not crop up till this past month (after I let it sit for a month or so).
I am going to eventually swap to the hall effect sticks cuz I like the idea, so my question is: Should I try to fix this issue in software (i.e. increase deadzones, would that be effective?), is there a quick hardware fix that I can do a without taking apart the Deck, or should I just go ahead and fastforward my timeline in getting and swapping to the Hall effect sticks? I figure if I have to open the Deck I might as well do the swap, but I want to put that off as long as I can.
I believe this is called snap back and it’s been a problem in the smash bros community with gc controllers. I don’t know too much about it but I think the normal fix is installing capacitors to the sticks somehow. Probably requires soldering?
You could also try increasing the dead zones a little bit.
Thanks for giving me the term for the effect, it’s insanely hard to Google the issue without knowing what it is called. I have increased the deadzone a little bit and it has helped as far as I can tell. Looks like I get to put off the upgrade for a bit longer.
deleted by creator
deleted by creator
Nice!
My joycons - original ones even! - finally started to drift earlier this year, and I did the same thing replacing them with some hall effect ones. So far I’ve been really pleased with the results, though initially it was a little weird simply because the sticks themselves felt a tiny bit different than the original ones. But after using them for a bit they felt good.
My Joycons have survived BotW, AC:NH, Three Houses, Metroid Dread and Metroid Prime, which I all played religiously. But they finally started drifting during my early hours of TotK. I just bought the Gulikit ones, switched them in less than half an hour. Great experience, no complaints, just not drifting joy cons.
Those are the same ones I installed in my joycons, too. And looks like the same ones in the photo on this post.
I had the same experience with the usage, AND I played a lot of Smash Bros. on them which would, in theory, destroy them in no time. But they started to drift about two months before ToTK came out, and I couldn’t risk playing that all janky.
I played most of TOTK with a controller because my joycon camera drift really messed with the gyro. Got the hall effect sticks installed last week and I’m hoping this is the end of drift for me.
I saw a few posts on twitter about these hall effect sticks still presenting with drift even with calibration. Not sure why, but I hope it’s just user error that can be corrected and not another hardware problem.
I’ve had mine installed for at least a couple months now. Played a lot of Zelda with them, and so far I haven’t had any issues with them.
For me it was worth a shot to try because it was cheaper than buying new joycons. And I didn’t want to send them off right before Zelda came out since I didn’t know when they’d come back (and they’d still be susceptible to drift later on).
