I honestly don’t see a reason why it would hurt if there’s nothing wired to the breaker. And it feels safer than leaving the contacts exposed since the metal cover is open on those slots. But I’m not sure if that’s the proper way.

As for the wire, I think it’s more so quality control. If it’s new and you bought it then you know it’s high quality and if it doesn’t work you can warranty your own work, but you can’t warranty old equipment. But this is another one where I can’t see the harm in using it if I am replacing a short strand of wire and it is the right length. Like I said, it’s type NM cable so it seems to be equivalent to modern romex wire, just a different brand.

Ya, I know I need to jump the ground when wiring to power cable for the dryer. I was going to do 10/3 since I had the money for it, but lowes and Home Depot were both sold out when I went to pick it up. Whirlpool told me 10/2 would work so I just went with that in the effort of saving time. New dryer is delivered Tuesday so I want the wiring done before then. The 30a double pole breaker was easy though. Probably the least questionable part of this process

Yup, I already have the electrical tape to mark it. Though I was told I could mark it red or black and both are universal markings for hot wire. Is that wrong? It doesn’t matter here because I have red tape but for future reference it would be good to know

I just finished running the new wire. I really lucked out. My step dad has a 50’ fishing tape and a 10’ endoscope that I was able to borrow. I got a new 10/2 wire pushed through fine. I called whirlpool for the specifications and they said the dryer needs 30 amps and will work with 10/2 or 10/3 wire. I was gonna go for the 10/3 but both lowes and Home Depot were sold out so I went with the 10/2. Got a 25’ roll and it used most of it. Maybe a foot of slack

The insulation protects the stuff outside the wire from catching fire. The wires get hot while carrying a load. Neutrals always carry a load once the hot is powered on. Grounds only carry when something goes wrong such as a power surge. They carry excess electricity the neutral can’t handle and usually significantly less so they don’t get as hot. There’s no reason not to insulate a ground, and it arguably is safer, but the amount safer is noticeably less considering the extra cost. For a ground to get hot enough to catch something on fire several other safety measures would need to fail. In that regard it’s not necessary.

Always! I’ve been doing a lot of work but I still don’t mess with safety. Obviously the main will be shut off and I won’t be doing the work while home alone in case something does happen. But since it is 1 breaker, 1 wire, and 1 outlet all being replaced it does seem to be a pretty straight forward replacement

They are right. I was wrong. But the wire is getting replaced regardless. My step dad does a good bit of electrical work and said he doesn’t trust an aluminum ground on a 240v outlet

So, I have a problem with electricians. I’m running out of them lol. I’ve had 4 out already for other projects and I get quotes and in 2 cases even paid the first payment but no one actually shows up to do the work. So I have just been doing it myself.

That’s said, my step dad does a lot of electrical work so I do have a bit of help even if he’s not a full on electrician. He’s has tons of tools for this type of work and makes most identification pretty easy. He took a Quick Look at the picture and he said it needs replaced based on the fact that it has an aluminum ground so I am just going to run all new wire. At least I know now that it will be the right wire

Snaking wire without a guide for that distance is extremely tough. The normal way to swap out wire would be to tie the new wire to the end of the old and the pull the other end of the old. Since you can’t pull the old (it’s stapled and secured) you can’t pull the new through behind it.

To your edit, it should be 2 hots and a neutral is my understanding. Hots deliver electric and neutrals complete the circuit back to the back. In newer wiring the 4th is the ground but a 240v 3 wire has no ground. However, if it is a neutral it should be sheathed and individually insulated.

That being said, I’m not an electrician and most of this is just what I’ve learned from replacing outlets and rerunning 120v wire in this house. If an electrician wants to tell me I’m wrong I’m all ears

It does look bad and I plan to replace it regardless. I’m more so wondering if it needs replaced now. Wire is expensive and replacing this will be pretty extensive as I would need to tear out horse hair plaster to unstaple it from the studs. I’m not 100% on if it’s stapled or not but it’s tough to move and the other wires I replaced were stapled down so we had to tear open the plaster and run them that way. This would be going from 2nd story to basement through kitchen behind the sink so it’s not a quick job. If it needs replaced now I’m gonna need to cancel the whole weekend

BotW didn’t fit in any one timeline. It had components from all the timelines. However, they said it occurred at the end of all 3 timelines. So my headcannon was that there was a large merging event that combined the timelines back to 1. And I expected it to be a “reset” where games would only reference the story from that point forward to kind of “clean up” the past lore without dealing with it. That clearly didn’t happen since TotK was all about history

I feel like that should be the case, but Nintendo has put themselves in the corner by releasing an “official” timeline. But this would have been pretty easy to fix by simply not calling Rauru the first king of Hyrule. And not making him Zonai. If he’d been a Hylian king that wasn’t the first it would make perfect sense…

Honestly, I loved TotK. But it made me dislike BotW. I love BotW when it released, but TotK made it feel incomplete. So many people were worried about Totk being glorified DLC but what it ended up making was BotW into the early release beta.

But I do enjoy older games as well. I remember playing a link to the past growing up and getting lost in the puzzles. We actually broke the game in one of the dungeons by using a key on the wrong door and soft locking the game in an unbeatable state. Had to start everything over lol. That was the age when some of these games were actually difficult though. Playing oracle of ages on switch and I am flying through it. With about 30 minutes of play time I got the first dungeon completed pretty easily. I think Zelda has evolved quite a few times and each generation of players has their “golden years”

I can see why a lot of people say that. It really does start to break apart under a not-so-fine microscope. I was kind of hoping there was something I was missing that would explain why it didn’t make sense but maybe not…

I’ve been around so many sites trying to figure it out but the consensus is that no one really knows… it just kind of happened. It’s a legit photo and not shopped though

We’ve had a couple funny ones where I work. I provision users in our call centers phone system.

afriend@company.com is the most innocent one I’ve come across. Emails are only internal for us so no one really says anything since customers don’t see them

Sooo what, another 20k for California and everyone else splits the rest? Sorry, but it’s so difficult to get excited for this when I see these plans push more to California, but on the east coast I have a single fast charger within 30 miles (proof. No filters on PlugShare except limiting it to CCS. Since I don’t own a Tesla NACS is hidden. https://imgur.com/a/TUbTMh0)

They’ll cram them in every corner of every city, but the people who are worried about range are the ones outside of the city, not on major highways or anything. Btw, one of those doesn’t count since it’s a dealership and is for Nissan owners only.

Edit: Not sure why this keeps posting to your comment specifically. I’m replying to the main post, but it’s only posting as a reply to you. Weird