Canadian version:
Keep your stick on the ice. We’re all pullin’ for ya!
Keep your dick in a vice
I’m sad that guy went off the MAGA deep end.
Nooo, what D:
To be clear, I’m talking about AvE and not red green guy
Ahh good to know
I like it. The guy who played Al Boreland now lives a quiet life.
Tim Allen went pro-Trump, whined about snowflakes and not being able to make jokes anymore, watch Disney replace Buzz Lightyear’s voice and lose a bunch of other roles, and now is “politically neutral”.
Tim Allen has always been conservative. I’ve been rewatching Home Improvement and it kind of blows me away how much the show leans on gender stereotypes for its jokes! It was only the 1990s but it feels like ancient history now.
I haven’t seen the show in years but I remember it having a slightly ironic/subversive undercurrent? I always read Tim Taylor as a bit of a caricature, that his whole grunting macho overdo everything attitude almost always backfired on him and he’d be better off calming the fuck down.
Exhibit A: The character of Al Boreland, who is…well basically he’s Norm Abram. While still outwardly traditionally masculine, wearing a full beard, a flannel shirt a tool belt to his contractor’s job, he’s very secure in his manhood, confident without being macho, soft spoken and even gentle. A perfect foil to Tim Taylor, who finds kindred spirits in Clark Griswold and Jeremy “POWAAA” Clarkson. If you’re really on board with the MAGA alpha male bullshit, do you write a character like Al Boreland?
I think, like a lot of folks on the right, Tim Allen followed the Republican party as they sprinted toward fascism. I think Allen was in on the joke in the 1990s and became the joke in the 2010s.
The show totally played it straight with some very cringeworthy episodes in the early seasons. They started subverting it more and more as time went along.
Some of the stuff they stayed with for a very long time though. Al Borland was the butt of many jokes for not presenting as traditionally masculine, for his relationship with his mother, for being single, etc. At times it could be hard to watch, with Tim essentially bullying Al relentlessly. Of course everything is all great at the end of the episode but it rarely involved an apology from Tim!
I kind of want a show where Al is the main character but that’s just The New Yankee Workshop.
Despite all that I am really enjoying the rewatch. What makes the show great are the other characters: Al, Jill, and Wilson! Wilson is by far my favourite. Such a weird guy!
Never forget: Wilson got shot dead in Silverado.
Absolutely. He’s just moments away from having a Roseanne Barr moment in his career.
And his show Last Man Standing was a blatantly obvious Republican. I didn’t mind the show though because his kids were Democrat and they were a foil to him.
I don’t think so, Tim.
Noooo Commander Taggart noooo :( :( :(
I don’t think so, Tim.
- The table still wobbling
That also looks like me in college when my friends would complain that we didn’t have anything to smoke out of.
Or assembling IKEA furniture using instructions containing pictures.
Lego instructions > IKEA instructions. While I think both are excellent at language free building instructions, Lego are the true masters. IKEA targets adults with their instructions and are seen by a lot of people as tedious and confusing, Lego targets children and they make universally beloved building toys.
That’s me
Just look at the guy… he’s carrying ALL of the Ace Hardware bling!
Okay but like a shim or just a broken discarded piece of 2x4?
Or I guess the chaotic evil version of this is a twig with leaves on it.
Jokes on you I had to go buy a kitchen sink faucet and replace it 1st thing in the morning before going to bed for my night shift cause ours broke yesterday evening 9pm. I’m a IT guy with 0 plumbing skill.
Now you have 1 plumbing skill. :D
Wood? I just keep folding cardboard until it’s the proper thickness.
Cardboard is wood with extra steps.
He’s still a babe.
Toilet paper for me
folded paper napkin. they’re all wood products.
That’s why I skip a few steps and wipe my ass with tree bark.
I use a bidet
I use my fingers then I rinse them off in the sink.
Rub it under the table leg to balance the table.
As a woodworker, I’d do the same. Granted it would be a piece of wood with matching dimensions to the foot, but still just a piece of wood.
did you manage to sell any of them pocket hoses too?
Do you know for a four legs table no matter the floor it sits on. There is always a rotational position where all it’s legs touch ground at the same level.
For circular tables that are uneven you can just rotate the table until it sits right.
For square tables you may check the 90° angles to see if you are lucky.
Edit: This theory works with even legs + uneven (bumpy) floors. For your own safety do not test this the other way around.
That’s just so wildly not true that I can’t believe you didn’t work it out for yourself in the time it took you to type that up.
To test your theory, envision a floor that is a perfectly level pane of glass. Then picture a 4 legged table where one leg is just an eighth inch shorter than the other 3.
You can spin that table all day and there’s never going to be a position where it doesn’t wobble.
@daniskarma@lemmy.dbzer0.com is citing a mathematical proof that basically states if you have a table whose feet form 4 points on a flat rectangle, that table can find a stable resting spot anywhere on an uneven surface only by rotating the table, you do not have to translate the table, only rotate it.
Your example, while practical, breaks that model because it only works if the continuous surface is uneven and the four independent points are coplaner. If you make the reverse true, with a table that has 4 even legs and put it on a floor that can be described as two triangles (what you would get if you connected 3 even length legs and one shorter) you could rotate the table to find somewhere all four legs touch.
This is why it is very important for us woodworkers to make table and chair legs the same length, or failing that, add adjustable feet, becasue us carpenters don’t know what the fuck we’re doing.
Yep, it works the other way around. Even legs uneven floor.
Interesting that it works the other way…I assume that in that scenario, there’s also no guarantee that the table would be anywhere close to level in whatever position eliminates wobble?
Not really how that works, but I dig the enthusiasm!
